|
Post by gonner on May 14, 2022 11:21:06 GMT -5
My attempt today at new zorsts,would have preffered Black. Mussent grumble they was cheap
|
|
bobf
New Member
Posts: 23
|
Post by bobf on May 23, 2022 12:21:19 GMT -5
Hi Jon - Did you get those adapter pipes made up, or did the exhausts come with them? After a recent road traffic accident I have to source some new exhausts, so I'm interested in any alternatives I can find.
Bob
|
|
|
Post by gonner on May 27, 2022 13:27:46 GMT -5
Hi Bob,had them made up in stainless steel by mijexhaust .There on e bay,sent a sketch with dimms and angle,2 days delivered...
|
|
|
Post by norwegian on Jun 15, 2022 10:23:31 GMT -5
Hello,
I need to replace both mufflers on my bike.
Hope you can tell med the name on the mufflers and where you hav eordered them.
Appreciate your answer
BR
Jarle Robertsen
|
|
|
Post by gonner on Jun 15, 2022 16:14:17 GMT -5
Hi Jarle,I did a search on e-bay for Reverse Cone Dunstal Exhaust,Silencers.Waited a few weeks until a sensible seller came along. They were EMGO WE38001,paid under a £100 for a brand new pair. There are a lot of Dreamers on there,so spend some time searching.. Hope that helps,John
|
|
|
Post by norwegian on Jun 16, 2022 7:01:09 GMT -5
Hi,
Thak you for your quick reply.
I contacted the MIJexhaust and asked if they can produce the same adatpter to me, here is what they write.
Thank you for your email. We can ship to NORWAY and yes that is something we make too. There is a couple of things I would like to point out before we discuss sizes, angles and prices; the part in the image has been adjusted to fit by the customer. We tell all our customers that the shortest length we make these in is 300mm overall length - if any end is NOT expanded then it can be cut down to length at the time of fitment. Which is I believe what the customer has done here, he has cut it down to length one the one side that wasn't expanded/flared and the end that was expanded to fit OVER the pipe has been left the same length as you can't cut that side down as the expansion is 50mm in length only.
and the other point was, the standard finish these are made in is the dull finish of the pipe, however we can polish these is requested and when fitted on bikes they must be polished as they are on show. Please remind us that this needs to be polished.
(we are a team of 4 and we all do the emails, sometimes not all the little bits of information are picked up, thus I mentioned the above)
What we need from you:
Please let us know the pipe size you require, the angle of the bend you require and if you need any of the ends expanded to fit OVER pipes or to butt against the existing pipes.
Is it possible for you to give me the size, angle, bend and the other tings they ask for. will be easier for me to order from MIJexhaust.
Will appreciate it very very much.
BR Jarle Robertsen
|
|
|
Post by gonner on Jun 17, 2022 9:37:38 GMT -5
Hi Jarle,I sent them a sketch like in the picture asking for a pair. You will need to verify sizes,my headers/downpipes are 43mm and I slid them into Exhausts using one of the adaptors that came with the Emgo silencers.Plus if you want slits,and polished!
Hope this helps
|
|
|
Post by norwegian on Jun 18, 2022 12:14:07 GMT -5
Hi,
Thank you very much, i have sent your last info to MIJexhaust.
BR
Jarle Robertsen
|
|