|
Post by rattler on Apr 5, 2015 1:19:58 GMT -5
Hi, Have a couple of drawings to use cartridge type filters for the TX 750. One uses a BMW filter element, the other a Honda. Enjoy.... bmw.pdf (31.59 KB) Print honda filter.pdf (54.47 KB)
|
|
|
Post by argo1974 on Apr 11, 2015 13:25:23 GMT -5
I just thought I'll post a picture of the pre-series part:
|
|
|
Post by albaljeu on Apr 22, 2015 22:22:02 GMT -5
Argo, where did you find that part ? Which filter does it use?
|
|
|
Post by roundporch on Mar 7, 2016 23:34:39 GMT -5
I have the .ems file you can use to open and get a quote from www.emachineshop.com/ will try to attach it. I did a run of 25 of them a few years ago. I'm just starting to get back into a '74 TX I've had for years. I found the best place to get the wix #24945 is rockauto. They normally sent the real WIX filter and not fram or other replacement version. See the attached photo there is a difference sometimes. Since these filters are normally 2 stacked together the real measure is total length. I found the wix to always be equal. I would do another run if there is interest (if I can get emachine shop to stop crashing) Cost is $15 at qty 25, then I put a filter and o-ring in there.
|
|
|
Post by minnesota750 on Apr 2, 2016 11:28:33 GMT -5
Argo - I will take one of them. Also, starter clutch works excellent!
|
|
|
Post by wanhedakru on May 23, 2017 10:33:34 GMT -5
Greetings All,
Does anyone have an oil adapter kit for sale or know where I can find one? It would be much appreciated!
:-)
|
|
|
Post by chuckhahn on Oct 21, 2017 8:32:20 GMT -5
What Honda filter is used on the Honda adapters???
|
|
pewe
New Member
Posts: 29
|
Post by pewe on Nov 1, 2017 3:23:42 GMT -5
The Honda adapter set needs FT500 filters.
|
|
deathbynissan55
New Member
Just picked up a '73, impressed with the dedication to this bike, lots of good info on here!
Posts: 35
|
Post by deathbynissan55 on Feb 5, 2018 0:17:01 GMT -5
So I made the one piece oil filter adapter designed to use the BMW filter shown here: I bought the same gasket that was used on the tx750 for the outer seal, that one works. However, none of thse seals that came with the Fram CH6060 match the size of the inner seal slot shown in the pic below: What do I have to buy for that inner seal. Also on that center bolt that holds everything together, what is the length and pitch? I believe its an M8, my guess is x 1.0, but need length since apparently you're supposed to get one a little bit longer than the original bolt. Any ideas on a cheap place to get the crush washer to would be appreciated. Thanks
|
|
|
Post by farmrjohn on Feb 5, 2018 11:02:10 GMT -5
Replied to your other post (saw it first). I don't recall the length for a longer bolt, but I took the original to the store got the next size longer. I then used it to close the cover on the case, noted how much room was left to the bolt head when it was bottomed in the case, then ground off that much plus a "smidge" from the threaded end.
|
|
|
Post by xpobxj on Aug 3, 2019 3:16:58 GMT -5
safe place to order viagra online canadian-pharmacyon.com <a href="http://canadian-pharmacyon.com/">what happens if a woman takes viagra</a>
|
|
fredi
New Member
www.tx750.de; community for germany, swiss and austria; Facebook IGTX750
Posts: 13
|
Post by fredi on Sept 4, 2021 4:13:06 GMT -5
2021:Kultmoto in Switzerland has produced a new (improved) oil filter adapter Yamaha TX 750 for BMW-filter. Can be ordered via homepage kultmoto (www.kultmoto.ch). A very easy to understand installation manual is included! Attachments:
|
|